Hotline
010-8840 8841
Your Current Position:  Products > Special Signal Generators

Nanosecond High Voltage pulsers

Nanosecond high-voltage pulse generator is based on new all solid-state semiconductor FID switch technology, which is dedicated to nanosecond electric field related research power platform architecture.

Picosecond High Voltage pulsers

● High switching rate and repetition frequency, which can be used in the fields of pokels cells drive, streak camera control, optical imaging and laser modulation drive, etc
● Extremely fast pulse output, which can be used for the test of UWB radar, phased antenna array, ground penetrating radar, UWB communication system and signal shield
● Signal source for EMI and EMC test
● Providing super fast high power pulse signal for particle accelerator

FPG-SP Ultra-Fast Pulsers

The rise time of FPG-SP series pulse generator ranges from 20 picoseconds to 100 picoseconds. FPG-SP series pulse generator is designed for the convenience of laboratory or industrial use. These pulse generators can be desktop or rack mounted.

High PRF Pulsers

FPG-HF high pulse repetition rate pulsers with PRF from 100 kHz to several megahertz. FPG-HF pulsers are manufactured in both desktop or rack mount housings and are convenient for laboratory or industrial use.

Multi-channel pulsers

In certain cases a high voltage nanosecond or picosecond pulse should be applied to a sustained load or simultaneously to several loads.FPG-X multichannel pulsers are designed for these applications.

Spike Generator Model 7054-2

The Model 7054-2 was especially designed for screen room use in applying high voltage transients at power line inputs to electronic equipment. The adjustable amplitude makes it possible to determine the threshold of susceptibility to spikes appearing on the power line. The Model 7054-2 may be used for performing tests per Method CS06 of MIL-STD-462, Method 5006.1 of MIL-STD-826A, various missile specifications and others.

Transient Generators Model 9354-1

The Model 9354-1 and 9354-2 Transient Generators were especially designed for the performance of a variety of pulse susceptibility tests on subsystems and/or equipment, in accordance with MIL-STD-461E/F/G, Method CS116; also capable of limited testing for RTCA DO-160D, Section 22.

Netwave Series Multi functional AC/DC Power Sources

The NetWave Series (3-phase) are three-phase AC/DC power source, specifically designed to fully meet the requirements as per the standards IEC/EN 61000-4-13, -4-14, -4-28 and in addition to pre compliance testing to -4-27.

Surge Generator

The generator PG1275E is specially designed for conducted susceptibility / transient tests to voltage surge and spikes of 28 Vdc electric circuits in military vehicles according to MIL-STD 1275E.

CS106 Pulse Generator

This generator is designed for the test of the transients conducted susceptibility of power leads according to MIL-STD-461F / CS106. These requirements are applicable to submarine and surface ship equipment and subsystem AC and DC input power leads. This pulse generator must be ordered with the active inductive coupler IC10M.

CS115 Rectangular Pulse Generator

This test generator is designed to comply with the requirements of the MIL-STD-461 CS115. The test method CS115 is used to verify the ability of the EUT to withstand pulse excitation on interconnecting cables. The pulse generator can be ordered with all the accessories in order to build the full test set-up basically consisting of an injection probe, an attenuator and an oscilloscope. The generator can be controlled by a computer through a RS232 or USB interface.

CS116 Damped Sinusoidal Generator

This test generator is designed to comply with the requirements of the MIL-STD 461 CS116. The test method CS116 is used to verify the ability of the EUT to withstand sinusoidal excitation on interconnecting cables. The pulse generator can be ordered with all the accessories in order to build the full test set-up, consisting basically of an injection probe, an attenuator and an oscilloscope.